QUICK LOAD Liners

Save time and money by loading your liners from the front!

Innovative QUICK LOAD® liners install from the front of the MIG gun in less than half the time required to install conventional liners, increasing uptime, cost savings and safety

Save even more with an upgrade to the Quick Load Liner Autolength System

  • Requires less than half the time and effort to replace (compared to conventional liners)
  • Two-piece system with retainer installed inside the power pin on first use
  • Liner portion feeds from the front of the MIG gun
  • No need to cut and waste wire!
  • Avoid climbing over robotic tooling or transfer systems to remove the torch from the wire feeder
  • Change the liner from a safe zone in the robotic work cell
  • No need to climb up to change liners in semi-automatic MIG guns connected to boom mounted feeders

QUICK LOAD Liner System Components

The QUICK LOAD liner system is a two-piece system that requires the following components:

  • QUICK LOAD liner
  • QUICK LOAD liner retainer (installed inside the power pin on first use)

Specifications

  • Available for 0.023″ (0.6 mm) – 3/32″ (2.4 mm) wire sizes
  • Available in lengths of up to 15 feet for robotic applications
  • Available in lengths of up to 25 feet for semi-automatic applications

Product Compatibility

QUICK LOAD Liners

Part NumberDescription
415-30-15Qfor 0.030″ wire, 15′ length; high carbon steel – round wound
415-35-6Qfor 0.035″ – 0.045″ wire, 6′ length; high carbon steel – round wound
415-35-10Qfor 0.035″ – 0.045″ wire, 10′ length; high carbon steel – round wound
415-35-15Qfor 0.035″ – 0.045″ wire, 15′ length; high carbon steel – round wound
415-35-25Qfor 0.035″ – 0.045″ wire, 25′ length; high carbon steel – round wound
415-116-6Qfor 0.045″ – 1/16″ wire, 6′ length; high carbon steel – round wound
415-116-10Qfor 0.045″ – 1/16″ wire, 10′ length; high carbon steel – round wound
415-116-15Qfor 0.045″ – 1/16″ wire, 15′ length; high carbon steel – round wound
415-116-25Qfor 0.045″ – 1/16″ wire, 25′ length; high carbon steel – round wound
415-564-6Qfor 1/16″ – 5/64″ wire, 6′ length; high carbon steel – round wound
415-564-15Qfor 1/16″ – 5/64″ wire, 15′ length; high carbon steel – round wound
415-564-25Qfor 1/16″ – 5/64″ wire, 25′ length; high carbon steel – round wound
415-332-15Qfor 0.078″ – 3/32″ wire, 15′ length; high carbon steel – round wound; replaces conventional liner 415-332-15
415-332-25Qfor 0.078″ – 3/32″ wire, 25′ length; high carbon steel – round wound; replaces conventional liner 415-332-25

Back to Top

QUICK LOAD Liner Retainers

Required for initial installation only (sold separately)

Part NumberDescription
415-24*3/32″ wire
415-26*for 0.030″ – 5/64″ wire
415-37**for 0.030″ – 5/64″ wire

*Compatible with Tregaskiss® TOUGH GUN® robotic and fixed automatic MIG guns and Bernard® BTB and TGX® semi-automatic air-cooled MIG guns
** Compatible with most Tweco® MIG guns

Related Products